Manpages

NAME

st - SCSI tape device

SYNOPSIS

#include <sys/mtio.h>

int ioctl(int fd, int request [, (void *)arg3]);
int ioctl(int fd, MTIOCTOP, (struct mtop *)mt_cmd);
int ioctl(int fd, MTIOCGET, (struct mtget *)mt_status);
int ioctl(int fd, MTIOCPOS, (struct mtpos *)mt_pos);

DESCRIPTION

The st driver provides the interface to a variety of SCSI tape devices. Currently, the driver takes control of all detected devices of type “sequential-access”. The st driver uses major device number 9.

Each device uses eight minor device numbers. The lowermost five bits in the minor numbers are assigned sequentially in the order of detection. In the 2.6 kernel, the bits above the eight lowermost bits are concatenated to the five lowermost bits to form the tape number. The minor numbers can be grouped into two sets of four numbers: the principal (auto-rewind) minor device numbers, n, and the “no-rewind” device numbers, (n + 128). Devices opened using the principal device number will be sent a REWIND command when they are closed. Devices opened using the “no-rewind” device number will not. (Note that using an auto-rewind device for positioning the tape with, for instance, mt does not lead to the desired result: the tape is rewound after the mt command and the next command starts from the beginning of the tape).

Within each group, four minor numbers are available to define devices with different characteristics (block size, compression, density, etc.) When the system starts up, only the first device is available. The other three are activated when the default characteristics are defined (see below). (By changing compile-time constants, it is possible to change the balance between the maximum number of tape drives and the number of minor numbers for each drive. The default allocation allows control of 32 tape drives. For instance, it is possible to control up to 64 tape drives with two minor numbers for different options.)

Devices are typically created by:

mknod -m 666 /dev/st0 c 9 0
mknod -m 666 /dev/st0l c 9 32
mknod -m 666 /dev/st0m c 9 64
mknod -m 666 /dev/st0a c 9 96
mknod -m 666 /dev/nst0 c 9 128
mknod -m 666 /dev/nst0l c 9 160
mknod -m 666 /dev/nst0m c 9 192
mknod -m 666 /dev/nst0a c 9 224

There is no corresponding block device.

The driver uses an internal buffer that has to be large enough to hold at least one tape block. In kernels before 2.1.121, the buffer is allocated as one contiguous block. This limits the block size to the largest contiguous block of memory the kernel allocator can provide. The limit is currently 128 kB for 32-bit architectures and 256 kB for 64-bit architectures. In newer kernels the driver allocates the buffer in several parts if necessary. By default, the maximum number of parts is 16. This means that the maximum block size is very large (2 MB if allocation of 16 blocks of 128 kB succeeds).

The driver’s internal buffer size is determined by a compile-time constant which can be overridden with a kernel startup option. In addition to this, the driver tries to allocate a larger temporary buffer at run time if necessary. However, run-time allocation of large contiguous blocks of memory may fail and it is advisable not to rely too much on dynamic buffer allocation with kernels older than 2.1.121 (this applies also to demand-loading the driver with kerneld or kmod).

The driver does not specifically support any tape drive brand or model. After system start-up the tape device options are defined by the drive firmware. For example, if the drive firmware selects fixed-block mode, the tape device uses fixed-block mode. The options can be changed with explicit ioctl(2) calls and remain in effect when the device is closed and reopened. Setting the options affects both the auto-rewind and the nonrewind device.

Different options can be specified for the different devices within the subgroup of four. The options take effect when the device is opened. For example, the system administrator can define one device that writes in fixed-block mode with a certain block size, and one which writes in variable-block mode (if the drive supports both modes).

The driver supports tape partitions if they are supported by the drive. (Note that the tape partitions have nothing to do with disk partitions. A partitioned tape can be seen as several logical tapes within one medium.) Partition support has to be enabled with an ioctl(2). The tape location is preserved within each partition across partition changes. The partition used for subsequent tape operations is selected with an ioctl(2). The partition switch is executed together with the next tape operation in order to avoid unnecessary tape movement. The maximum number of partitions on a tape is defined by a compile-time constant (originally four). The driver contains an ioctl(2) that can format a tape with either one or two partitions.

Device /dev/tape is usually created as a hard or soft link to the default tape device on the system.

Starting from kernel 2.6.2, the driver exports in the sysfs directory /sys/class/scsi_tape the attached devices and some parameters assigned to the devices.

Data transfer
The driver supports operation in both fixed-block mode and variable-block mode (if supported by the drive). In fixed-block mode the drive writes blocks of the specified size and the block size is not dependent on the byte counts of the write system calls. In variable-block mode one tape block is written for each write call and the byte count determines the size of the corresponding tape block. Note that the blocks on the tape don’t contain any information about the writing mode: when reading, the only important thing is to use commands that accept the block sizes on the tape.

In variable-block mode the read byte count does not have to match the tape block size exactly. If the byte count is larger than the next block on tape, the driver returns the data and the function returns the actual block size. If the block size is larger than the byte count, an error is returned.

In fixed-block mode the read byte counts can be arbitrary if buffering is enabled, or a multiple of the tape block size if buffering is disabled. Kernels before 2.1.121 allow writes with arbitrary byte count if buffering is enabled. In all other cases (kernel before 2.1.121 with buffering disabled or newer kernel) the write byte count must be a multiple of the tape block size.

In the 2.6 kernel, the driver tries to use direct transfers between the user buffer and the device. If this is not possible, the driver’s internal buffer is used. The reasons for not using direct transfers include improper alignment of the user buffer (default is 512 bytes but this can be changed by the HBA driver), one or more pages of the user buffer not reachable by the SCSI adapter, and so on.

A filemark is automatically written to tape if the last tape operation before close was a write.

When a filemark is encountered while reading, the following happens. If there are data remaining in the buffer when the filemark is found, the buffered data is returned. The next read returns zero bytes. The following read returns data from the next file. The end of recorded data is signaled by returning zero bytes for two consecutive read calls. The third read returns an error.

Ioctls
The driver supports three ioctl(2) requests. Requests not recognized by the st driver are passed to the SCSI driver. The definitions below are from /usr/include/linux/mtio.h:

MTIOCTOP — perform a tape operation
This request takes an argument of type (struct mtop *). Not all drives support all operations. The driver returns an EIO error if the drive rejects an operation.

/* Structure for MTIOCTOP - mag tape op command: */
struct mtop {
    short   mt_op;       /* operations defined below */
    int     mt_count;    /* how many of them */
};

Magnetic tape operations for normal tape use:

MTCOMPRESSION

Enable compression of tape data within the drive if mt_count is nonzero and disable compression if mt_count is zero. This command uses the MODE page 15 supported by most DATs.

MTERASE

Erase tape. With 2.6 kernel, short erase (mark tape empty) is performed if the argument is zero. Otherwise, long erase (erase all) is done.

MTMKPART

Format the tape into one or two partitions. If mt_count is positive, it gives the size of partition 1 and partition 0 contains the rest of the tape. If mt_count is zero, the tape is formatted into one partition. From kernel version 4.6, a negative mt_count specifies the size of partition 0 and the rest of the tape contains partition 1. The physical ordering of partitions depends on the drive. This command is not allowed for a drive unless the partition support is enabled for the drive (see MT_ST_CAN_PARTITIONS below).

MTRESET

Reset drive.

MTRETEN

Re-tension tape.

MTSETBLK

Set the drive’s block length to the value specified in mt_count. A block length of zero sets the drive to variable block size mode.

MTSETDENSITY

Set the tape density to the code in mt_count. The density codes supported by a drive can be found from the drive documentation.

MTSETPART

The active partition is switched to mt_count. The partitions are numbered from zero. This command is not allowed for a drive unless the partition support is enabled for the drive (see MT_ST_CAN_PARTITIONS below).

MTUNLOAD

Execute the SCSI unload command (does not eject the tape).

MTUNLOCK

Unlock the tape drive door.

Magnetic tape operations for setting of device options (by the superuser):
MTSETDRVBUFFER

Set various drive and driver options according to bits encoded in mt_count. These consist of the drive’s buffering mode, a set of Boolean driver options, the buffer write threshold, defaults for the block size and density, and timeouts (only in kernels 2.1 and later). A single operation can affect only one item in the list below (the Booleans counted as one item.)

A value having zeros in the high-order 4 bits will be used to set the drive’s buffering mode. The buffering modes are:

To control the write threshold the value in mt_count must include the constant MT_ST_WRITE_THRESHOLD bitwise ORed with a block count in the low 28 bits. The block count refers to 1024-byte blocks, not the physical block size on the tape. The threshold cannot exceed the driver’s internal buffer size (see DESCRIPTION, above).

To set and clear the Boolean options the value in mt_count must include one of the constants MT_ST_BOOLEANS, MT_ST_SETBOOLEANS, MT_ST_CLEARBOOLEANS, or MT_ST_DEFBOOLEANS bitwise ORed with whatever combination of the following options is desired. Using MT_ST_BOOLEANS the options can be set to the values defined in the corresponding bits. With MT_ST_SETBOOLEANS the options can be selectively set and with MT_ST_DEFBOOLEANS selectively cleared.

MT_ST_BUFFER_WRITES (Default: true)

Buffer all write operations in fixed-block mode. If this option is false and the drive uses a fixed block size, then all write operations must be for a multiple of the block size. This option must be set false to write reliable multivolume archives.

MT_ST_ASYNC_WRITES (Default: true)

When this option is true, write operations return immediately without waiting for the data to be transferred to the drive if the data fits into the driver’s buffer. The write threshold determines how full the buffer must be before a new SCSI write command is issued. Any errors reported by the drive will be held until the next operation. This option must be set false to write reliable multivolume archives.

MT_ST_READ_AHEAD (Default: true)

This option causes the driver to provide read buffering and read-ahead in fixed-block mode. If this option is false and the drive uses a fixed block size, then all read operations must be for a multiple of the block size.

MT_ST_TWO_FM (Default: false)

This option modifies the driver behavior when a file is closed. The normal action is to write a single filemark. If the option is true, the driver will write two filemarks and backspace over the second one.

Note: This option should not be set true for QIC tape drives since they are unable to overwrite a filemark. These drives detect the end of recorded data by testing for blank tape rather than two consecutive filemarks. Most other current drives also detect the end of recorded data and using two filemarks is usually necessary only when interchanging tapes with some other systems.

MT_ST_DEBUGGING (Default: false)

This option turns on various debugging messages from the driver (effective only if the driver was compiled with DEBUG defined nonzero).

MT_ST_FAST_EOM (Default: false)

This option causes the MTEOM operation to be sent directly to the drive, potentially speeding up the operation but causing the driver to lose track of the current file number normally returned by the MTIOCGET request. If MT_ST_FAST_EOM is false, the driver will respond to an MTEOM request by forward spacing over files.

MT_ST_AUTO_LOCK (Default: false)

When this option is true, the drive door is locked when the device file is opened and unlocked when it is closed.

MT_ST_DEF_WRITES (Default: false)

The tape options (block size, mode, compression, etc.) may change when changing from one device linked to a drive to another device linked to the same drive depending on how the devices are defined. This option defines when the changes are enforced by the driver using SCSI-commands and when the drives auto-detection capabilities are relied upon. If this option is false, the driver sends the SCSI-commands immediately when the device is changed. If the option is true, the SCSI-commands are not sent until a write is requested. In this case, the drive firmware is allowed to detect the tape structure when reading and the SCSI-commands are used only to make sure that a tape is written according to the correct specification.

MT_ST_CAN_BSR (Default: false)

When read-ahead is used, the tape must sometimes be spaced backward to the correct position when the device is closed and the SCSI command to space backward over records is used for this purpose. Some older drives can’t process this command reliably and this option can be used to instruct the driver not to use the command. The end result is that, with read-ahead and fixed-block mode, the tape may not be correctly positioned within a file when the device is closed. With 2.6 kernel, the default is true for drives supporting SCSI-3.

MT_ST_NO_BLKLIMS (Default: false)

Some drives don’t accept the READ BLOCK LIMITS SCSI command. If this is used, the driver does not use the command. The drawback is that the driver can’t check before sending commands if the selected block size is acceptable to the drive.

MT_ST_CAN_PARTITIONS (Default: false)

This option enables support for several partitions within a tape. The option applies to all devices linked to a drive.

MT_ST_SCSI2LOGICAL (Default: false)

This option instructs the driver to use the logical block addresses defined in the SCSI-2 standard when performing the seek and tell operations (both with MTSEEK and MTIOCPOS commands and when changing tape partition). Otherwise, the device-specific addresses are used. It is highly advisable to set this option if the drive supports the logical addresses because they count also filemarks. There are some drives that support only the logical block addresses.

MT_ST_SYSV (Default: false)

When this option is enabled, the tape devices use the System V semantics. Otherwise, the BSD semantics are used. The most important difference between the semantics is what happens when a device used for reading is closed: in System V semantics the tape is spaced forward past the next filemark if this has not happened while using the device. In BSD semantics the tape position is not changed.

MT_NO_WAIT (Default: false)

Enables immediate mode (i.e., don’t wait for the command to finish) for some commands (e.g., rewind).

An example:

struct mtop mt_cmd;
mt_cmd.mt_op = MTSETDRVBUFFER;
mt_cmd.mt_count = MT_ST_BOOLEANS |
        MT_ST_BUFFER_WRITES | MT_ST_ASYNC_WRITES;
ioctl(fd, MTIOCTOP, mt_cmd);

MTIOCGET — get status
This request takes an argument of type (struct mtget *).

/* structure for MTIOCGET - mag tape get status command */
struct mtget {
    long     mt_type;
    long     mt_resid;
    /* the following registers are device dependent */
    long     mt_dsreg;
    long     mt_gstat;
    long     mt_erreg;
    /* The next two fields are not always used */
    daddr_t  mt_fileno;
    daddr_t  mt_blkno;
};

mt_type

The header file defines many values for mt_type, but the current driver reports only the generic types MT_ISSCSI1 (Generic SCSI-1 tape) and MT_ISSCSI2 (Generic SCSI-2 tape).

mt_resid

contains the current tape partition number.

mt_dsreg

reports the drive’s current settings for block size (in the low 24 bits) and density (in the high 8 bits). These fields are defined by MT_ST_BLKSIZE_SHIFT, MT_ST_BLKSIZE_MASK, MT_ST_DENSITY_SHIFT, and MT_ST_DENSITY_MASK.

mt_gstat

reports generic (device independent) status information. The header file defines macros for testing these status bits:

operation).

operation).

operation).

mt_erreg

The only field defined in mt_erreg is the recovered error count in the low 16 bits (as defined by MT_ST_SOFTERR_SHIFT and MT_ST_SOFTERR_MASK). Due to inconsistencies in the way drives report recovered errors, this count is often not maintained (most drives do not by default report soft errors but this can be changed with a SCSI MODE SELECT command).

mt_fileno

reports the current file number (zero-based). This value is set to -1 when the file number is unknown (e.g., after MTBSS or MTSEEK).

mt_blkno

reports the block number (zero-based) within the current file. This value is set to -1 when the block number is unknown (e.g., after MTBSF, MTBSS, or MTSEEK).

MTIOCPOS — get tape position
This request takes an argument of type (struct mtpos *) and reports the drive’s notion of the current tape block number, which is not the same as mt_blkno returned by MTIOCGET. This drive must be a SCSI-2 drive that supports the READ POSITION command (device-specific address) or a Tandberg-compatible SCSI-1 drive (Tandberg, Archive Viper, Wangtek, ... ).

/* structure for MTIOCPOS - mag tape get position command */
struct mtpos {
    long mt_blkno;    /* current block number */
};

RETURN VALUE

EOVERFLOW

An attempt was made to read or write a variable-length block that is larger than the driver’s internal buffer.

FILES

/dev/st*

the auto-rewind SCSI tape devices

/dev/nst*

the nonrewind SCSI tape devices

NOTES

SEE ALSO

mt(1)

The file drivers/scsi/README.st or Documentation/scsi/st.txt (kernel >= 2.6) in the Linux kernel source tree contains the most recent information about the driver and its configuration possibilities

COLOPHON

This page is part of release 5.09 of the Linux man-pages project. A description of the project, information about reporting bugs, and the latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.