Linux Manpages Online - man.cx manual pages

SYNOPSIS

tc ... action pedit [ex] munge { RAW_OP | LAYERED_OP | EXTENDED_LAYERED_OP } [ CONTROL ]

RAW_OP := offset OFFSET { u8 | u16 | u32 } [ AT_SPEC ] CMD_SPEC

AT_SPEC := at AT offmask MASK shift SHIFT

LAYERED_OP := { ip IPHDR_FIELD | ip BEYOND_IPHDR_FIELD } CMD_SPEC

EXTENDED_LAYERED_OP := { eth ETHHDR_FIELD | ip IPHDR_FIELD | ip EX_IPHDR_FIELD | ip6 IP6HDR_FIELD | tcp TCPHDR_FIELD | udp UDPHDR_FIELD } CMD_SPEC

ETHHDR_FIELD := { src | dst | type }

IPHDR_FIELD := { src | dst | tos | dsfield | ihl | protocol | precedence | nofrag | firstfrag | ce | df }

BEYOND_IPHDR_FIELD := { dport | sport | icmp_type | icmp_code }

EX_IPHDR_FIELD := { ttl }

IP6HDR_FIELD := { src | dst | traffic_class | flow_lbl | payload_len | nexthdr | hoplimit }

TCPHDR_FIELD := { sport | dport | flags }

UDPHDR_FIELD := { sport | dport }

CMD_SPEC := { clear | invert | set VAL | add VAL | decrement | preserve } [ retain RVAL ]

CONTROL := { reclassify | pipe | drop | shot | continue | pass | goto chain CHAIN_INDEX }

The pedit action can be used to change arbitrary packet data. The location of data to change can either be specified by giving an offset and size as in RAW_OP, or for header values by naming the header and field to edit the size is then chosen automatically based on the header field size.

OPTIONS

Use extended pedit. EXTENDED_LAYERED_OP and the add/decrement CMD_SPEC are allowed only in this mode.

offset OFFSET { u32 | u16 | u8 }

Specify the offset at which to change data. OFFSET is a signed integer, it’s base is automatically chosen (e.g. hex if prefixed by 0x or octal if prefixed by 0). The second argument specifies the length of data to change, that is four bytes (u32), two bytes (u16) or a single byte (u8).

at AT offmask MASK shift SHIFT

This is an optional part of RAW_OP which allows one to have a variable OFFSET depending on packet data at offset AT, which is binary ANDed with MASK and right-shifted by SHIFT before adding it to OFFSET.

eth ETHHDR_FIELD

Change an ETH header field. The supported keywords for ETHHDR_FIELD are:

	src
	dst		Source or destination MAC address in the standard format: XX:XX:XX:XX:XX:XX
	type		Ether-type in numeric value

ip IPHDR_FIELD

Change an IPv4 header field. The supported keywords for IPHDR_FIELD are:

	src
	dst		Source or destination IP address, a four-byte value.
	tos

dsfield
precedence

Type Of Service field, an eight-bit value.

ihl

Change the IP Header Length field, a four-bit value.

protocol

Next-layer Protocol field, an eight-bit value.

nofrag

firstfrag

	ce
	df
	mf		Change IP header flags. Note that the value to pass to the set command is not just a bit value, but the full byte including the flags field. Though only the relevant bits of that value are respected, the rest ignored.

ip BEYOND_IPHDR_FIELD

Supported only for non-extended layered op. It is passed to the kernel as offsets relative to the beginning of the IP header and assumes the IP header is of minimum size (20 bytes). The supported keywords for BEYOND_IPHDR_FIELD are:

	dport
	sport		Destination or source port numbers, a 16-bit value. Indeed, IPv4 headers don’t contain this information. Instead, this will set an offset which suits at least TCP and UDP if the IP header is of minimum size (20 bytes). If not, this will do unexpected things.

icmp_type
icmp_code

Again, this allows one to change data past the actual IP header itself. It assumes an ICMP header is present immediately following the (minimal sized) IP header. If it is not or the latter is bigger than the minimum of 20 bytes, this will do unexpected things. These fields are eight-bit values.

ip EX_IPHDR_FIELD

Supported only when ex is used. The supported keywords for EX_IPHDR_FIELD are:

ttl

ip6 IP6HDR_FIELD

The supported keywords for IP6HDR_FIELD are:

	src
	dst

traffic_class
flow_lbl
payload_len
nexthdr
hoplimit

tcp TCPHDR_FIELD

The supported keywords for TCPHDR_FIELD are:

	sport
	dport		Source or destination TCP port number, a 16-bit value.
	flags

udp UDPHDR_FIELD

The supported keywords for UDPHDR_FIELD are:

	sport
	dport		Source or destination TCP port number, a 16-bit value.
	clear

Clear the addressed data (i.e., set it to zero).

invert

Swap every bit in the addressed data.

set VAL

Set the addressed data to a specific value. The size of VAL is defined by either one of the u32, u16 or u8 keywords in RAW_OP, or the size of the addressed header field in LAYERED_OP.

add VAL

Add the addressed data by a specific value. The size of VAL is defined by the size of the addressed header field in EXTENDED_LAYERED_OP. This operation is supported only for extended layered op.

decrement

Decrease the addressed data by one. This operation is supported only for ip ttl and ip6 hoplimit.

preserve

Keep the addressed data as is.

retain RVAL

This optional extra part of CMD_SPEC allows one to exclude bits from being changed. Supported only for 32 bits fields or smaller.

CONTROL

The following keywords allow one to control how the tree of qdisc, classes, filters and actions is further traversed after this action.
reclassify

Restart with the first filter in the current list.

	pipe		Continue with the next action attached to the same filter.
	drop
	shot		Drop the packet.

continue

Continue classification with the next filter in line.

pass

Finish classification process and return to calling qdisc for further packet processing. This is the default.

EXAMPLES

Being able to edit packet data, one could do all kinds of things, such as e.g. implementing port redirection. Certainly not the most useful application, but as an example it should do:

First, qdiscs need to be set up to attach filters to. For the receive path, a simple ingress qdisc will do, for transmit path a classful qdisc (HTB in this case) is necessary:

tc qdisc replace dev eth0 root handle 1: htb
tc qdisc add dev eth0 ingress handle ffff:

Finally, a filter with pedit action can be added for each direction. In this case, u32 is used matching on the port number to redirect from, while pedit then does the actual rewriting:

tc filter add dev eth0 parent 1: u32 \

	match ip dport 23 0xffff \
	action pedit pedit munge ip dport set 22