NAME
ppbus — Parallel Port Bus system
SYNOPSIS
device ppbus
device vpo
device lpt
device plip
device ppi
device pps
device lpbb
DESCRIPTION
The ppbus system provides a uniform, modular and architecture-independent system for the implementation of drivers to control various parallel devices, and to utilize different parallel port chipsets.
DEVICE DRIVERS
In order to write new drivers or port existing drivers, the ppbus system provides the following facilities:
•
architecture-independent macros or functions to access parallel ports
•
mechanism to allow various devices to share the same parallel port
•
a user interface named ppi(4) that allows parallel port access from outside the kernel without conflicting with kernel-in drivers.
Developing
new drivers
The ppbus system has been designed to support the
development of standard and non-standard software:
Driver
Description
vpo VPI0 parallel to Adaptec AIC-7110 SCSI controller
driver. It uses standard and non-standard parallel port
accesses.
ppi Parallel port interface for general I/O
pps Pulse per second Timing Interface
lpbb Philips official parallel port I2C bit-banging
interface
Porting
existing drivers
Another approach to the ppbus system is to port existing
drivers. Various drivers have already been ported:
Driver
Description
lpt lpt printer driver
plip lp parallel network interface driver
ppbus should let you port any other software even from other operating systems that provide similar services.
PARALLEL PORT CHIPSETS
Parallel port chipset support is provided by ppc(4).
The ppbus system provides functions and macros to allocate a new parallel port bus, then initialize it and upper peripheral device drivers.
ppc makes chipset detection and initialization and then calls ppbus attach functions to initialize the ppbus system.
PARALLEL PORT MODEL
The logical parallel port model chosen for the ppbus system is the PC’s parallel port model. Consequently, for the i386 implementation of ppbus, most of the services provided by ppc are macros for inb() and outb() calls. But, for an other architecture, accesses to one of our logical registers (data, status, control...) may require more than one I/O access.
Description
The parallel port may operate in the following modes:
•
compatible mode, also called Centronics mode
•
bidirectional 8/4-bits mode, also called NIBBLE mode
•
byte mode, also called PS/2 mode
•
Extended Capability Port mode, ECP
•
Enhanced Parallel Port mode, EPP
•
mixed ECP+EPP or ECP+PS/2 modes
Compatible
mode
This mode defines the protocol used by most PCs to transfer
data to a printer. In this mode, data is placed on the
port’s data lines, the printer status is checked for
no errors and that it is not busy, and then a data Strobe is
generated by the software to clock the data to the
printer.
Many I/O controllers have implemented a mode that uses a FIFO buffer to transfer data with the Compatibility mode protocol. This mode is referred to as "Fast Centronics" or "Parallel Port FIFO mode".
Bidirectional
mode
The NIBBLE mode is the most common way to get reverse
channel data from a printer or peripheral. Combined with the
standard host to printer mode, it provides a complete
bidirectional channel.
In this mode, outputs are 8-bits long. Inputs are accomplished by reading 4 of the 8 bits of the status register.
Byte mode
In this mode, the data register is used either for outputs
and inputs. Then, any transfer is 8-bits long.
Extended
Capability Port mode
The ECP protocol was proposed as an advanced mode for
communication with printer and scanner type peripherals.
Like the EPP protocol, ECP mode provides for a high
performance bidirectional communication path between the
host adapter and the peripheral.
ECP protocol features include:
Run_Length_Encoding (RLE) data compression for host adapters
FIFOs for both the forward and reverse channels
DMA as well as programmed I/O for the host register interface.
Enhanced
Parallel Port mode
The EPP protocol was originally developed as a means to
provide a high performance parallel port link that would
still be compatible with the standard parallel port.
The EPP mode has two types of cycle: address and data. What makes the difference at hardware level is the strobe of the byte placed on the data lines. Data are strobed with nAutofeed, addresses are strobed with nSelectin signals.
A particularity of the ISA implementation of the EPP protocol is that an EPP cycle fits in an ISA cycle. In this fashion, parallel port peripherals can operate at close to the same performance levels as an equivalent ISA plug-in card.
At software level, you may implement the protocol you wish, using data and address cycles as you want. This is for the IEEE1284 compatible part. Then, peripheral vendors may implement protocol handshake with the following status lines: PError, nFault and Select. Try to know how these lines toggle with your peripheral, allowing the peripheral to request more data, stop the transfer and so on.
At any time, the peripheral may interrupt the host with the nAck signal without disturbing the current transfer.
Mixed
modes
Some manufacturers, like SMC, have implemented chipsets that
support mixed modes. With such chipsets, mode switching is
available at any time by accessing the extended control
register.
IEEE1284-1994 Standard
Background
This standard is also named "IEEE Standard Signaling
Method for a Bidirectional Parallel Peripheral Interface for
Personal Computers". It defines a signaling method for
asynchronous, fully interlocked, bidirectional parallel
communications between hosts and printers or other
peripherals. It also specifies a format for a peripheral
identification string and a method of returning this string
to the host outside of the bidirectional data stream.
This standard is architecture independent and only specifies dialog handshake at signal level. One should refer to architecture specific documentation in order to manipulate machine dependent registers, mapped memory or other methods to control these signals.
The IEEE1284 protocol is fully oriented with all supported parallel port modes. The computer acts as master and the peripheral as slave.
Any transfer is defined as a finite state automaton. It allows software to properly manage the fully interlocked scheme of the signaling method. The compatible mode is supported "as is" without any negotiation because it is compatible. Any other mode must be firstly negotiated by the host to check it is supported by the peripheral, then to enter one of the forward idle states.
At any time, the slave may want to send data to the host. This is only possible from forward idle states (nibble, byte, ecp...). So, the host must have previously negotiated to permit the peripheral to request transfer. Interrupt lines may be dedicated to the requesting signals to prevent time consuming polling methods.
But peripheral requests are only a hint to the master host. If the host accepts the transfer, it must firstly negotiate the reverse mode and then starts the transfer. At any time during reverse transfer, the host may terminate the transfer or the slave may drive wires to signal that no more data is available.
Implementation
IEEE1284 Standard support has been implemented at the top of
the ppbus system as a set of procedures that perform high
level functions like negotiation, termination, transfer in
any mode without bothering you with low level
characteristics of the standard.
IEEE1284 interacts with the ppbus system as little as possible. That means you still have to request the ppbus when you want to access it, the negotiate function does not do it for you. And of course, release it later.
ARCHITECTURE
adapter, ppbus and device
layers
First, there is the adapter layer, the lowest of the
ppbus system. It provides chipset abstraction throw a set of
low level functions that maps the logical model to the
underlying hardware.
Secondly, there is the ppbus layer that provides functions to:
1.
share the parallel port bus among the daisy-chain like connected devices
2.
manage devices linked to ppbus
3.
propose an arch-independent interface to access the hardware layer.
Finally, the device layer gathers the parallel peripheral device drivers.
Parallel
modes management
We have to differentiate operating modes at various ppbus
system layers. Actually, ppbus and adapter operating modes
on one hands and for each one, current and available modes
are separated.
With this level of abstraction a particular chipset may commute from any native mode to any other mode emulated with extended modes without disturbing upper layers. For example, most chipsets support NIBBLE mode as native and emulated with ECP and/or EPP.
This architecture should support IEEE1284-1994 modes.
FEATURES
The boot process
The boot process starts with the probe stage of the ppc(4)
driver during ISA bus (PC architecture) initialization.
During attachment of the ppc driver, a new ppbus structure
is allocated, then probe and attachment for this new bus
node are called.
ppbus attachment tries to detect any PnP parallel peripheral (according to Plug and Play Parallel Port Devices draft from (c)1993-4 Microsoft Corporation) then probes and attaches known device drivers.
During probe, device drivers are supposed to request the ppbus and try to set their operating mode. This mode will be saved in the context structure and returned each time the driver requests the ppbus.
Bus
allocation and interrupts
ppbus allocation is mandatory not to corrupt I/O of other
devices. Another usage of ppbus allocation is to reserve the
port and receive incoming interrupts.
High level interrupt handlers are connected to the ppbus system thanks to the newbus BUS_SETUP_INTR() and BUS_TEARDOWN_INTR() functions. But, in order to attach a handler, drivers must own the bus. Consequently, a ppbus request is mandatory in order to call the above functions (see existing drivers for more info). Note that the interrupt handler is automatically released when the ppbus is released.
Microsequences
Microsequences is a general purpose mechanism to allow
fast low-level manipulation of the parallel port.
Microsequences may be used to do either standard (in
IEEE1284 modes) or non-standard transfers. The philosophy of
microsequences is to avoid the overhead of the ppbus layer
and do most of the job at adapter level.
A microsequence is an array of opcodes and parameters. Each opcode codes an operation (opcodes are described in microseq(9)). Standard I/O operations are implemented at ppbus level whereas basic I/O operations and microseq language are coded at adapter level for efficiency.
As an example, the vpo(4) driver uses microsequences to implement:
•
a modified version of the NIBBLE transfer mode
•
various I/O sequences to initialize, select and allocate the peripheral
SEE ALSO
lpt(4), plip(4), ppc(4), ppi(4), vpo(4)
HISTORY
The ppbus manual page first appeared in FreeBSD 3.0.
AUTHORS
This manual page was written by Nicolas Souchu.
BSD March 1, 1998 BSD