NAME
pmlogger_daily_report - write Performance Co-Pilot daily summary reports
SYNOPSIS
$PCP_BINADM_DIR/pmlogger_daily_report [-ApV?] [-a archivefile] [-f outputfile] [-h hostname] [-l logfile] [-o directory] [-t interval]
DESCRIPTION
pmlogger_daily_report writes daily performance summary reports, much like those produced by sadc(1) and the sa2(8) utility.
All of the command line arguments are optional and intended to be self explanatory.
By default, the reports are not generated, but if the pcp-zeroconf package has been installed (there will be files in $PCP_VAR_DIR/config/pmlogconf/zeroconf) then the necessary metrics will have been included in the default pmlogger(1) configuration file and the reports will be generated.
The reports are generated (by default) soon after midnight, once pmlogger_daily(1) has completed the merging of any partal archives to generate one archive for yesterday’s activity.
Each performance summary report is named sarXX (where XX is yesterdays day-of-the-month). The outputfile may be changed with the -f option. The report will be written to the $PCP_LOG_DIR/sa directory by default, but this may be changed with the -o option to a different directory.
Note that there are suffciently flexible command line options for pmlogger_daily_report to be used to read any archivefile and write the report to any output directory.
If the -a option is not given, the default input archivefile is $PCP_ARCHIVE_DIR/HOSTNAME/YYYYMMDD, where HOSTNAME defaults to the local hostname (unless changed with the -h option) and YYYYMMDD is the base name of yesterdays merged archive, as produced by pmlogger(1) and pmlogger_daily(1). If archivefile is a directory, then pmlogger_daily_report will use all PCP archives found in that directory to write the report (this is known as multi-archive mode, and may be considerably slower than specifying a single archive as the input).
The reports themselves are created by the pmrep(1) utility using its default configuration file, see pmrep.conf(5). The pmrep(1) configuration entries used to write the reports is currently hardwired into the pmlogger_daily_report script.
Finally, the input archives must contain sufficient metrics as needed by pmrep(1) to write the report. On platforms that support it, the pcp-zeroconf package configures PCP logging as required for this - hence pmlogger_daily_report should be used with the pmlogger(1) configuration that is set up by pcp-zeroconf. As the name suggests, pcp-zeroconf requires no additional configuration after installation in order to capture the required archives needed by pmlogger_daily_report.
OPTIONS
The available
command line options are:
-a archive
Specifies an alternate input archive file basename or directory path.
|
-A |
Use the start and end times of input archive for the report, as opposed to the default behaviour of 24 hours from midnight yesterday. |
-f filename
Specifies an alternate output filename. -h hostname Specifies an alternateA hostname to use within the default input archive file path.
-l file, --logfile=file
In order to ensure that mail is not unintentionally sent when this script is run from pmlogger_daily(1) diagnostics are always sent to a log file. By default, this file is $PCP_LOG_DIR/pmlogger/pmlogger_daily_report.log but this can be changed using the -l option. If this log file already exists when the script starts, it will be renamed with a .prev suffix (overwriting any log file saved earlier) before diagnostics are generated to the log file.
|
-p |
If this option is specified then the status of the daily processing is polled and if the report has not been done in the last 24 hours then it is done now. With this option, pmlogger_daily_report simply exits if the previous day’s processing has already been done. |
This option is no longer required as the polling of pmlogger_daily(1) will ensure the report will be generated, however the option is retained for backwards compatibility.
-t interval
Specifies the sampling interval used when generating the report, in the format described in PCPIntro(1). The default is every 10 minutes.
-V, --verbose
The output from the execution of the script may be extended using this option which enables verbose tracing of activity. By default the script generates no log output unless some error or warning condition is encountered.
-?, --help
Display usage message and exit.
PCP ENVIRONMENT
Environment variables with the prefix PCP_ are used to parameterize the file and directory names used by PCP. On each installation, the file /etc/pcp.conf contains the local values for these variables. The $PCP_CONF variable may be used to specify an alternative configuration file, as described in pcp.conf(5).
SEE ALSO
PCPIntro(1), pmlogger_daily(1), pmlogger(1), pmrep(1), sadc(1) and sa2(8).