NAME
iftab - static information about the network interfaces
DESCRIPTION
The file /etc/iftab contains descriptive information about the various network interfaces. iftab is only used by the program ifrename(8) to assign a consistent network interface name to each network interface.
/etc/iftab defines a set of mappings. Each mapping contains an interface name and a set of selectors. The selectors allow ifrename to identify each network interface on the system. If a network interface matches all descriptors of a mapping, ifrename attempt to change the name of the interface to the interface name given by the mapping.
MAPPINGS
Each mapping is described on a separate line, it starts with an interface name, and contains a set of descriptors, separated by space or tabs.
The relationship between descriptors of a mapping is a logical and. A mapping matches a network interface only is all the descriptors match. If a network interface doesn’t support a specific descriptor, it won’t match any mappings using this descriptor.
If you want to use alternate descriptors for an interface name (logical or), specify two different mappings with the same interface name (one on each line). Ifrename always uses the last matching mapping in iftab.
INTERFACE NAME
The first part of each mapping is an interface name. If a network interface matches all descriptors of a mapping, ifrename attempt to change the name of the interface to the interface name given by the mapping.
The interface name of a mapping is either a plain interface name (such as eth2 or wlan1) or a interface name pattern containing a single wildcard (such as eth* or wlan*). In case of wildcard, the kernel replace the ’*’ with the lowest available integer making this interface name unique. Note that wildcard is only supported for kernel 2.6.1 and 2.4.30 and later.
It is
discouraged to try to map interfaces to default interfaces
names such as eth0, wlan0 or ppp0. The
kernel use those as the default name for any new interface,
therefore most likely an interface will already use this
name and prevent ifrename to use it. Even if you use
takeover, the interface may already be up in some cases. Not
using those name will allow you to immediately spot
unconfigured or new interfaces.
Good names are either totally unique and meaningfull, such
as mydsl or privatehub, or use larger integer,
such as eth5 or wlan5. The second type is
usually easier to integrate in various network
utilities.
DESCRIPTORS
Each descriptor is composed of a descriptor name and descriptor value. Descriptors specify a static attribute of a network interface, the goal is to uniquely identify each piece of hardware.
Most users will
only use the mac selector despite its potential
problems, other selectors are for more specialised setup.
Most selectors accept a ’*’ in the selector
value for wilcard matching, and most selectors are case
insensitive.
mac mac address
Matches the MAC Address of the
interface with the specified MAC address. The MAC address of
the interface can be shown using ifconfig(8) or
ip(8).
This is the most common selector, as most interfaces have a
unique MAC address allowing to identify network interfaces
without ambiguity. However, some interfaces don’t have
a valid MAC address until they are brought up, in such case
using this selector is tricky or impossible.
arp arp type
Matches the ARP Type (also
called Link Type) of the interface with the specified ARP
type as a number. The ARP Type of the interface can be shown
using ifconfig(8) or ip(8), the
link/ether type correspond to 1 and the
link/ieee802.11 type correspond to 801.
This selector is useful when a driver create multiple
network interfaces for a single network card.
driver driver name
Matches the Driver Name of the interface with the specified driver name. The Driver Name of the interface can be shown using ethtool -i(8).
businfo bus information
Matches the Bus Information of the interface with the specified bus information. The Bus Information of the interface can be shown using ethtool -i(8).
firmware firmware revision
Matches the Firmware Revision of the interface with the firmware revision information. The Firmware Revision of the interface can be shown using ethtool -i(8).
baseaddress base address
Matches the Base Address of the
interface with the specified base address. The Base Address
of the interface can be shown using ifconfig(8).
Because most cards use dynamic allocation of the Base
Address, this selector is only useful for ISA and EISA
cards.
irq irq line
Matches the IRQ Line
(interrupt) of the interface with the specified IRQ line.
The IRQ Line of the interface can be shown using
ifconfig(8).
Because there are IRQ Lines may be shared, this selector is
usually not sufficient to uniquely identify an
interface.
iwproto wireless protocol
Matches the Wireless Protocol
of the interface with the specified wireless protocol. The
Wireless Protocol of the interface can be shown using
iwconfig(8) or iwgetid(8).
This selector is only supported on wireless interfaces and
is not sufficient to uniquely identify an interface.
pcmciaslot pcmcia slot
Matches the Pcmcia Socket
number of the interface with the specified slot number.
Pcmcia Socket number of the interface can be shown using
cardctl ident(8).
This selector is usually only supported on 16 bits cards,
for 32 bits cards it is advised to use the selector
businfo.
prevname previous interface name
Matches the name of the
interface prior to renaming with the specified oldname.
This selector should be avoided as the previous interface
name may vary depending on various condition. A
system/kernel/driver update may change the original name.
Then, ifrename or another tool may rename it prior to the
execution of this selector.
SYSFS{filename} value
Matches the content the sysfs
attribute given by filename to the specified value. For
symlinks and parents directories, match the actual directory
name of the sysfs attribute given by filename to the
specified value.
A list of the most useful sysfs attributes is given in the
next section.
SYSFS DESCRIPTORS
Sysfs attributes for a specific interface are located on most systems in the directory named after that interface at /sys/class/net/. Most sysfs attribute are files, and their values can be read using cat(1) or more(1). It is also possible to match attributes in subdirectories.
Some sysfs attributes are symlinks, pointing to another directory in sysfs. If the attribute filename is a symlink the sysfs attribute resolves to the name of the directory pointed by the symlink using readlink(1). The location is a directory in the sysfs tree is also important. If the attribute filename ends with /.., the sysfs attribute resolves to the real name of the parent directory using pwd(1).
The sysfs filesystem is only supported with 2.6.X kernel and need to be mounted (usually in /sys). sysfs selectors are not as efficient as other selectors, therefore they should be avoided for maximum performance.
These are
common sysfs attributes and their corresponding ifrename
descriptors.
SYSFS{address} value
Same as the mac descriptor.
SYSFS{type} value
Same as the arp descriptor.
SYSFS{device} value
Valid only up to kernel 2.6.20. Same as the businfo descriptor.
SYSFS{..} value
Valid only from kernel 2.6.21. Same as the businfo descriptor.
SYSFS{device/driver} value
Valid only up to kernel 2.6.20. Same as the driver descriptor.
SYSFS{../driver} value
Valid only from kernel 2.6.21. Same as the driver descriptor.
SYSFS{device/irq} value
Valid only up to kernel 2.6.20. Same as the irq descriptor.
SYSFS{../irq} value
Valid only from kernel 2.6.21. Same as the irq descriptor.
EXAMPLES
# This is a comment
eth2 |
mac 08:00:09:DE:82:0E | |||
eth3 |
driver wavelan interrupt 15 baseaddress 0x390 | |||
eth4 |
driver pcnet32 businfo 0000:02:05.0 | |||
air* |
mac 00:07:0E:* arp 1 | |||
myvpn |
SYSFS{address} 00:10:83:* SYSFS{type} 1 | |||
bcm* |
SYSFS{device} 0000:03:00.0 SYSFS{device/driver} bcm43xx | |||
bcm* |
SYSFS{..} 0000:03:00.0 SYSFS{../driver} bcm43xx |
AUTHOR
Jean Tourrilhes - jt [AT] hpl.com
FILES
/etc/iftab
SEE ALSO
ifrename(8), ifconfig(8), ip(8), ethtool(8), iwconfig(8).